Electronics & Communication / SSB-SC Filter Method
FREE TO EXPLORE
LABORATORY 04 · ELECTRONICS & COMMUNICATION

Single-Sideband Suppressed-Carrier (SSB-SC) Generation via Crystal Lattice Filter

Generate an upper sideband (USB) SSB-SC signal using a balanced modulator and high-Q crystal bandpass ladder filter, determining unwanted sideband rejection and linear transfer gain. Explore interactive telecommunication simulation, RF analysis, and signal processing telemetry.

ANALOG MODULATION · DIGITAL BASEBAND · PASSBAND MODULATION · ANTENNAS & RF · OPTICAL FIBER · DSP

Your virtual electronics & communication engineering laboratory.

SSB-SC FILTERED OUTPUT AMPLITUDE V_SSB—
RF INSTRUMENTATION TELEMETRY

Ready to sample with Audio Input Amplitude = 1.0 V.

1.0 V
Excitation locked to low-phase-noise synthesized reference oscillator.

Adjust Audio Input Amplitude, then execute telecommunication RF/baseband acquisition.

Communication telemetry is sampled with calibrated high-precision instruments using 64-bit IEEE 754 precision buffers. Residuals reflect ordinary least-squares regression across successive observations. Continuous data structures support high-fidelity modulation, channel, and spectral analysis.

Communication engineering assumptions and boundary limits

Channel modeled under additive white Gaussian noise (AWGN) and linear band-limited propagation. Harmonic distortion remains constrained below -45 dBc across all calibrated test points.

Laboratory apparatus & testing equipment.

SSB-SC Filter Method Telecommunication Workstation

Provides regulated RF/baseband excitation, precision impedance-matched test fixtures, and low-noise interconnection for unwanted sideband attenuation, power efficiency & coherent bfo demodulation.

6.5-Digit True-RMS Digital Multimeter (Keysight / Fluke)

Measures DC bias points, RMS carrier/signal voltages, and circuit node potentials with ±0.0035% baseline accuracy.

Four-Channel Digital Storage Oscilloscope (200 MHz, 2 GSa/s)

Captures high-frequency RF envelopes, baseband eye diagrams, constellation patterns, and transient responses for ssb-sc filter method.

Synthesized Vector RF Signal Generator (9 kHz – 3 GHz)

Delivers calibrated, low-phase-noise continuous-wave and modulated carrier signals to establish audio input amplitude conditions.

High-Dynamic-Range RF Spectrum Analyzer (9 kHz – 3.6 GHz)

Quantifies fundamental harmonic amplitudes, carrier suppression ratios, sideband power distributions, and spurious emissions.

Matched 50-Ohm Coaxial Interconnects & Attenuator Set

Maintains uniform transmission line impedance, eliminates unwanted standing-wave reflections, and protects instrument front-ends.

FOLLOW THE METHOD

A reason behind every step.

Generate an upper sideband (USB) SSB-SC signal using a balanced modulator and high-Q crystal bandpass ladder filter, determining unwanted sideband rejection and linear transfer gain. Standardized parameter settings: 0.2, 0.5, 0.8, 1.2, 1.6, 2.0 V.

  1. Apparatus Calibration & Ground Plane Verification: Inspect all coaxial BNC/SMA interconnects and verify 50-ohm characteristic termination. Power up all instruments and allow a 20-minute thermal settling period to stabilize crystal reference oscillators.
  2. Carrier & Modulating Signal Synthesis: Configure the synthesized RF signal generator and baseband source to the specified baseline parameters. Calibrate the audio input amplitude using the precision digital multimeter and oscilloscope.
  3. Systematic Telemetry Acquisition & Setpoint Stepping: Increment the audio input amplitude systematically across the experimental range (0.2 to 2.0 V), logging the resulting ssb-sc filtered output amplitude v_ssb after signal settling.
  4. Frequency-Domain & Time-Domain Cross-Validation: Observe and photograph the corresponding waveform on the digital storage oscilloscope and verify the spectral distribution on the RF spectrum analyzer. Verify that harmonic distortion remains below -45 dBc.
  5. Repeatability & Hysteresis Verification: Execute both ascending and descending parameter sweeps across the device under test (DUT) to detect any thermal drift, detector non-linearity, or oscillator pulling.
  6. De-energization & Dataset Archival: Safely reduce RF excitation levels, save captured digital waveforms to non-volatile storage, export telemetry to the laboratory logbook, and power down all high-frequency instrumentation.
YOUR NOTEBOOK · 0 OBSERVATIONS

Turn measurements into telecommunication engineering insight.

See a complete example report ↗

Points are your recorded observations. The solid regression line validates SSB-SC Filter Method mathematical scaling.

LINEAR REGRESSION FIT · y = mx + b
V_ssb = 0.7500 · V_in
#Baseband Audio Input Amplitude V_in (V)SSB-SC Filtered Output Amplitude V_ssb (V)Baseband input amplitude V_in (V)SSB-SC output amplitude V_ssb (V)

No readings yet. Execute a communication trial and record it.

CHECK YOUR UNDERSTANDING

Explain what the communication metrics mean.

Question 1: In the experimental investigation of SSB-SC Filter Method, the primary dependent variable measured is:

Question 2: The mathematical relationship governing SSB-SC Filter Method is modeled as:

Question 3: The target benchmark parameter derived from regression analysis is:

Question 4: Which instrument provides the most accurate visualization of spectral harmonics and carrier sidebands in the frequency domain?

THEORY AND ELECTROMAGNETIC CONTEXT

Electronics & Communication Engineering background & physical principles.

Generate an upper sideband (USB) SSB-SC signal using a balanced modulator and high-Q crystal bandpass ladder filter, determining unwanted sideband rejection and linear transfer gain.

V_ssb = 0.7500 · V_in

Communication systems rely on Fourier spectral decomposition, Shannon channel capacity, and electromagnetic propagation theory.